In most cases, toy haulers come equipped with four basic recessed D-ring tie-down anchors, one at each corner of the garage area. This works well for securing heavier ATVs and UTVs. But when it comes time to transport motorcycles or dirt bikes, we must choose from a plethora of aftermarket devices intended to do just that.
However, not all restraint systems work as intended, especially while riding in the back of a bouncy toy hauler. What you think might work just fine can turn into an expensive travel disaster should a part of it fail while in motion. So how does one avoid a tangled pile of dirt bikes and gear at the trailhead?
We did a little investigation and found a system that not only works but is so darn simple to install, even a child could figure it out. The product comes from a company called Bolt It On, which was funny because their Motorcycle Restraint System didn't actually require any bolts at all. In fact, this particular system didn't even require any tools to mount or use.
It's available in four different configurations, able to secure two, four, six or even eight dirt bikes with no hassle whatsoever. The installation process reminded us of erecting one of those E-Z Up tents; simply slide the parts in place, tension the unit in place and snap the locking pins-you're ready to load motorcycles. It's that easy.
The kit arrived as two separate parcels via UPS. The long, square crossbar was packed separately in a long cardboard tube. The remaining brackets were individually wrapped in newspaper and packaged together in one medium-size box. We were impressed with the fact that the only thing we had to do was unwrap the newspaper from each part and start building.
Instructions were included, too, but kind of like an excited child on Christmas morning, we skipped right to the installation process. The system went together in less than 10 minutes.
We installed it on a toy hauler and can offer these tips:
โข If you've never used your toy hauler's anchor points, you won't have to remove the carpet to access the tie-downs; simply slice a hole directly over the center of the D-ring.
โข Prior to loading a motorcycle, double-check the tightness of the J-hook tensioned knobs. These should be cranked down enough to prevent any side-to-side movement of the rack.
FEATURES:
โข 100% Tool-free installation
โข Remove and replace in 5 minutes
โข Laser-cut carbon steel for strength
โข V-style wheel chocks keep bike secure
โข Chocks available for dirt, sport and cruisers
โข Mounts to D-rings for safe and secure transport
โข Lightweight and user-friendly
ย
In the modern digital age, a โhackโ is generally defined as a clever or elegant solution to a nagging problem. The phrase โThereโs a hack for thatโ seems to be a common expression nearly synonymous with saying โGet with the times, man!โ
Well, Iโm pleased to say that Iโve discovered a hack for transporting motorcycles that has increased my overall quality of life measurablyโthe Bolt It On Rack System for transporting motorcycles.
Weโve all experienced our fair share of trials and tribulations when it comes to loading and hauling motorcycles, especially when venturing beyond the truck bed to an enclosed trailer or toy-hauler.
The aptly named toy hauler has become a popular way to transport dirt bikes, while simultaneously dragging along your mobile estate. By featuring fold-up furniture and a large rear door that doubles as a loading ramp, a toy hauler provides for motorcycle storage directly in the camper itself, freeing up the truck bed for firewood and other essentials, and eliminating the need to disconnect the truck from the trailer upon arrival.
Sounds like the perfect transport solution, right? Well, almost. Put yourself in this scenario:
Itโs early Friday afternoon before a three-day holiday weekend and youโve left the office a little early to beat city traffic with hopes of rushing home to hook up the toy hauler and embark on a long-awaited family motorcycle weekend.
Timing is critical, so youโve asked your wife to constantly monitor Waze to deliver blow-by-blow traffic and route updates to ensure an on-time arrival. Your kids are in the backseat surrounded by snacks and physically wrestling over the iPad, while the baby is crying because heโs been restrained in the car seat for too long amid all of the chaos. All you can think about is the shoddy menagerie of tie-downs, laid-over bike stands, and gear bags you used to haphazardly secure the motorcycles in the back of your toy hauler.
Of course, without being able to see your precious two-wheeled cargo while youโre pulling the enclosed toy-hauler, it becomes a mental game of pokerโbluffing yourself that your mess will hold together until you arrive, but knowing that you really have a losing hand and should mitigate the severity of the situation, pronto. Your better judgment temporarily intervenes and you decide to make an ill-timed pit stop on the side of the freeway to take a peek, for better or for worse.
Praying that you and your rig do not get rear-ended, you make your way back to the toy hauler door. Before you can even reach for the handle, you already hear the audible beep from the CO2 alarm, meaning only one thingโa fuel spill. There is at least one bike down, maybe more.
You open the door to discover your failed web of tie-downs in a heap on the floor. To your horror, all four motorcycles lying flat as pancakes. To make matters worse, the fuel vapor is so thick you can hardly breathe. As you turn to run out the door, you notice two holes punched through the interior wall from wayward handlebars and additional holes in the floor.
As youโve probably surmised by now, this is a true story. It happened to me. I was completely at fault and, unfortunately, itโs a day that my family will never let me forget. Thereโs got to be a better way!
The folks at Bolt It On have hacked this problem and created a completely practical and fail-safe way to transport your precious two-wheeled beauties. Bolt It On founder Scott Corgiat realized the obviousโRV manufacturers are not designing cargo areas specifically for motorcycles.
Instead, they provide a series of D-rings in the floor and itโs up to the purchaser to formulate a way to securely Spider-man their bikes in an upright position without causing any collateral damage. This typically takes at least four tie-downs per bike, and is a crap shoot at best.
The Bolt It On Rack System is essentially a powdercoated steel bar that utilizes two J-hooks looped through the D-rings in the RV floor to secure it down. Motorcycle wheel chocks can be configured on either side of the bar and tie down anchor points can be positioned to maximize effectiveness.
Corgiatโs team delivered an 80-inch bar with two regular wheel chocks and one extended chock on one side of the bar, and a fourth wheel chock on the other. This configuration will accommodate three bikes on one side and a fourth bike on the other, facing the other three. Depending on the particular RV floor plan, one Bolt It On Rack System can accommodate as many as eight motorcycles.
Assembly instructions were clear and concise and Bolt It On has plenty of pictures on Instagram for those of us who are visual learners. Either way, assembly and configuration are straightforward and intuitive.
Securing the rack to the floor of the RV takes less than 90 secondsโjust turn a knob to tighten the J-hooks on the D-rings. Unexpectedly, you donโt actually bolt on the Bolt It On Rack System, and thatโs part of the beauty of it.
Every dirt bike has its own wheel chock and dedicated tie-down hooks. Loading and securing the motorcycles to the Bolt It On Rack System is much quicker and easier than loading up the truck bed for a day ride. Upon arrival, reverse the process to remove the rack for storage, either inside the toy hauler towards the rear or outside underneath the rig.
According to Corgiat, there is a truck bed version in the works, and perhaps even color-options for those diehards that want to match their favorite team color. Currently, there is a sport bike version, as well as a Bolt It On Rack System for cruisers, up to and including full dressers. Thereโs also a version for vans.
Itโs not often that a product comes along that makes so much sense that you wonder how you ever got along without it. The Bolt It On Rack System for motorcycle transport system should be standard equipment directly from the RV dealerโitโs that essential.
